Troubleshooting Maytag F74 Error Code

Do you own a Maytag washer and have experienced the F74 error code? You’re not alone. Many Maytag washer owners have faced this troubling issue. Fortunately, there’s a way to fix it. Read on to learn more about the F74 error code, its root cause, and how you can resolve it yourself.

The F74 error code indicates a motor control unit (MCU) problem. This can be caused by a problem with an internal connection or a faulty MCU. In some cases, the problem may be caused by having too much soap or fabric softener in the control panel drawer. The best way to diagnose and determine exactly what’s causing the F74 error code is to remove the Washer’s outer case and use a multimeter to test the wiring harness.

If your Washer has no power, it’s best to start by checking the power cord and the circuit breaker. If these are both working correctly, then you may need to proceed to troubleshoot the wiring. Pay special attention for any loose or broken terminals or wires. If everything checks out ok, then the problem may be the MCU itself and will need to be replaced.

Before attempting to replace the MCU, be sure to disconnect the power from the Washer. Once the power is disconnected, you can then remove the control panel cover in order to gain access to the MCU. Once the part is safely removed, you will then need to transfer the wiring to the new part and reconnect the power. After completed, restore the Washer’s outer case and the issue should be resolved.

In order to fix the F74 error code on Maytag Washers, you will need to troubleshoot the wiring harness and, in some cases, even replace the motor control unit (MCU). Doing this yourself can be challenging and time-consuming, so we recommend enlisting the help of a qualified appliance repair technician. Our directory of Appliance Repair Technicians can help connect you with professionals in your area who can easily diagnose and resolve this issue quickly and safely.

We hope that this guide has helped you understand the root cause of the F74 error code in Maytag Washers and has given you the confidence to either troubleshoot or enlist the help of a qualified repair technician to resolve the issue.

For more service and repair guides like this, make sure to visit our Directory of Appliance Repair Technicians to find the best fit for your home appliance needs.

FAQ on Fixing the F74 Error Code on Maytag Washers

  1. What does the F74 error code on my Maytag washer indicate? The F74 error code indicates a system-level failure in your Maytag washer.
  2. What can I do to resolve the F74 error code on my Maytag washer? You can try unplugging the washer for at least 10 minutes in order to reset the system. Alternatively, you can check your hoses for kinks and make sure that nothing is blocking the drain pump.
  3. How can I check if the issue has been resolved? Once you’ve unplugged the washer and cleared any blockages, run a diagnostic cycle by pressing and holding the Power/Cycle key for 3 seconds. If the code is still present, the issue is likely unresolved.
  4. Are there any other solutions to try? If you’ve already attempted the steps mentioned above, it’s best to contact a certified service technician to further investigate.
  5. If I need to replace a part, what is covered under my Maytag warranty? If the repair is covered by your Maytag warranty, you may be eligible for a free replacement part. To check your warranty coverage, please refer to your Maytag user’s manual.

Key Takeaways: Fixing Maytag F74 Error Code

  1. The F74 error code indicates a problem with the Motor Control Unit (MCU).
  2. Too much soap or fabric softener in the control panel drawer can be a potential cause.
  3. To diagnose and determine exactly what’s causing the F74 error code, remove the Washer’s outer case and use a multimeter to test the wiring harness.
  4. If the problem is with the MCU, you will need to disconnect the power, remove the control panel cover and replace the MCU.
  5. If troubleshooting the issue is difficult, we recommend enlisting the help of a qualified appliance repair technician.